This page sponsored by JT's Stockroom    [other banners]

	TSR : Web boards : M/s D/s O&P : "Ankle /wrist stocks" Ankle /wrist stocks (6) This post is on the M/s D/s O&P web board. Fri 13 Mar 09, 3:54 PM slave_najah_of_VARR CA, 3 yrs I enjoy placement in ankle wrist stocks and find it forces my butt in the air pleasure just fine. I was wondering if anyone has new ideas of how to make use of the stock or how one could modify the stock to create some pain? thank you 14 Mar 09, 2:33 AM Eclectic1 US(ID), 4 yrs Since there are various forms of stocks I would have to see the one you are referring to that you were thinking of modifying. Like anything else though, one is only limited by their imagination. 14 Mar 09, 6:09 AM 996-150-083 4 yrs As a punishment, I have been placed in a pillory (neck and wrists restrained) with my ankles cuffed to a spreader bar. Mistress Tamara then buckled an open mouth gag on me and placed my butt plug in my mouth and a large strap on dildo was then made available for several female dom friends of Mistress Tamara to use to f*** my rear - extremely humiliating. Spanked Slave 996-150-083 Edited 14 Mar 09, 6:10 AM by 996-150-083 26 Apr 09, 2:06 AM Mastery1 US(CA), 5 yrs Y! These are quite easy to make and also inexpensive. Best yet, all you need is a saber saw and a screwdriver. Material cost is less that $10 1)Purchase 2 locking hasps and loops (available at any .99 cent or dollar store). 2)Purchase one 8' 2X4, and have them cut it exactly in half (2 4' pieces). 3) Lay the two halves side by side. 4) Cut a neck hole in the center about 6" in diameter, (use a lunch plate as a template). 5) Cut 2 wrist holes on either side of the neck hole, (ovals are best). 6) Cut two ankle holes further out on each side. 7) ROUND the edges of all holes, (this is very VERY important). 8) Line the holes with leather or other padding. 9) Attach the hasps to each end. 10) Paint or stain and varnish to suit. You now have a rectangular piece of wood with 5 holes: a large neck hole in the center, 2 wrist holes (one one each side of the neck hole, and 2 ankle holes. This can now be used as EITHER a neck and wrist stock OR as an ankle and wrist stock, (...just not both at the same time). HAVE FUN | O o ( ) 0 o | Edited 27 Apr 09, 5:59 AM by Mastery1 22 May 09, 9:13 AM 401-033-260 US(NY), 3 yrs Y! MASTER liked your device but modified it as follows: Master used metal rather than leather or other soft lining in all 5 holes. Then Master bore a small hole in the middle just next to the neck hole in which He placed a small locking ring. This allows for my locking slave collar to be attached to the device by a short locking chain when the device is used as wrist and ankle stocks. Likewise it allows ankle cuffs to be attached via a locking chain when the device is used as a head and wrist stock. By simple adjusting the length of the attached chain Master forces my slave meat to be curled and bunched up awkwardly as much or little as He desires. Master also cut off the curved ends of an ordinary adjustible metal curtain rod and drilled holes in various places along the length of the adjustible rod. This permits Master to place a small lock lock attaching one end of the curtain rod to my slave collar while the other end locks the curtain rod to these stocks now used as ankle and wrist stocks. Alternativly the device can now be used as neck and wrist stocks and the curtain rod can lock the other end into an ordinary spreader bar locked on my slave ankles. In either case the curtain rod adds an completely rigid attachment between the stocks on the one hand and either my slave collar or spreader bar on the other depending on how the device is being used on my slave meat. The reason for positioning holes at various places - and also for using an adjustible rod is that this rigid 5 point bondage devise can now be adjusted in length as Master sees fit to accomicate my slave meat in various positions so my slave meat can be positioned standing, kneeling, curled up, etc. however Master sees fit with both ends being loced in place ridgedly. The is also permits the riged curtain rod attachment to be used on diferent slaves of different sizes. After my slave meat is properly postioned with the adjustable curtain rod positioned approriately Master attaches a third lock in the middle to lock the two parts of the curtain rod that slide past each other together to keep them from sliding and keep the entire contraption rigid. Finally Master later modified this further to add to the absolute rigidity of the curtain rod by fitting a round long thin piece of wood through both cut off ends of the curtain rod to provide extra strength and stop it from bending at all. The only trick here (as Master kindly explained to me) was to ensure that the wood was narrow enough to accomidate the small opening size of the inside of the curtain rod together with and width of the narrow rings used at in the middle and at both end attachment points and the two ends of the curtain rod which are used to attach the stock device on one and and either my slave collar or spreader bar on the other. 24 May 09, 8:18 PM slave_najah_of_VARR CA, 3 yrs thank you both for wonderful ideas 24 May 09, 8:35 PM 401-033-260 US(NY), 3 yrs Y! your welcome, sis.